Burley 09 Encore Uživatelský manuál Strana 1

Procházejte online nebo si stáhněte Uživatelský manuál pro Svítilny Burley 09 Encore. Burley 09 Encore User's Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 2
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
Contents:
(1) Burley Owner’s Instruction and Safety Manual
(1) Hitch
(1) Clear light with batteries included
(1) Red light with batteries included
(2) Phillip Pan screws
(2) Brackets for lights
(1) Wheel guard assembly:
(2) wheel guards
(4) screws
(1) 5mm hex key wrench
Tools Required: Phillips screwdriver
4mm hex wrench
10mm or open end wrench
Note: Consult your Burley Owner’s
Instruction and Safety Manual for
wheel guard and hitch installation
instructions.
Roll Bar Installation
1. If handle bar receivers are already
installed, loosen and remove handle bar
knobs and outer handle bar receivers.
FIGURE 1
2. Using wrench, loosen and remove
lock nuts and screws from handle bar
receivers.
3. From trailer front, slide roll bar into upper
handle bar receivers, with curved front
extending above trailer body.
4. Match holes in roll bar and inner handle
bar receivers, re-install screws and
tighten lock nuts.
5. Replace outer handle bar receivers and
tighten knobs.
Installation Instructions
for ‘09 d’lite
, Encore
®
and Solo
(Euro) Child Trailers
Contents:
(1) Burley Owner’s Instruction and Safety Manual
(1) Hitch
(1) Clear light with batteries included
(1) Red light with batteries included
(2) Phillip Pan screws
(2) Brackets for lights
(1) Wheel guard assembly:
(2) wheel guards
(4) screws
(1) 5mm hex key wrench
Tools Required: Phillips screwdriver
4mm hex wrench
10mm or open end wrench
Note: Consult your Burley Owner’s
Instruction and Safety Manual for
wheel guard and hitch installation
instructions.
Roll Bar Installation
1. If handle bar receivers are already
installed, loosen and remove handle bar
knobs and outer handle bar receivers.
FIGURE 1
2. Using wrench, loosen and remove
lock nuts and screws from handle bar
receivers.
3. From trailer front, slide roll bar into upper
handle bar receivers, with curved front
extending above trailer body.
4. Match holes in roll bar and inner handle
bar receivers, re-install screws and
tighten lock nuts.
5. Replace outer handle bar receivers and
tighten knobs.
Installation Instructions
for ‘09 d’lite
, Encore
®
and Solo
(Euro) Child Trailers
FIGURE 1: Roll Bar Installation
Lock Nuts
Rear Assembly
Frame
Roll Bar
Front of Trailer
Inner Handle bar
Receiver
Outer Handle bar
Receiver
Handle bar
Knob
Screws
FIGURE 1: Roll Bar Installation
Lock Nuts
Rear Assembly
Frame
Roll Bar
Front of Trailer
Inner Handle bar
Receiver
Outer Handle bar
Receiver
Handle bar
Knob
Screws
Zobrazit stránku 0
1 2

Shrnutí obsahu

Strany 1 - Roll Bar Installation

Contents:(1) Burley Owner’s Instruction and Safety Manual(1) Hitch(1) Clear light with batteries included(1) Red light with batteries included(2) Phil

Strany 2

B U R L E Y D E S I G NCopyright © 2008 by Burley Design LLC. “Burley” is a registered trademark of Burley Design LLC : Rev 06/08 : 170056 Euro d’l

Komentáře k této Příručce

Žádné komentáře